IDEA: Rosy Three Strand Bracelet

Rosy Three Strand Bracelet
We have made this pretty bracelet with our alluring and sparkly Swarovski crystals in both fuchsia and rose. The crystals are accented with peachy pink seed beads with an AB finish. The combination is truly delightful. The finished length is approximately 6 6/8 inches. There will be a few crystals left to increase the length if needed.

Materials:
1 Pkg. Sterling Silver Heishi, 4mm (#27503) Qty:
1 Pkg. Fuchsia Swarovski Bicone Crystals, 3mm (#16517) Qty:
1 Pkg. Fuchsia Swarovski Bicone Crystals, 4mm (#16518) Qty:
1 Pkg. Rose Swarovski Bicone Crystals, 6mm (#16532) Qty:
1 Pkg. Lined Pink/Peach AB Seed Bead, 11/0 (#J-832) Qty:
1 Pkg. Sterling Silver Crimp Tubes, 2x1mm (#50054) Qty:
1 Pkg. Sterling Silver Crimp Covers (#50060) Qty:
1 Pkg. S/P Filigree Clasp, 3 strand (#50130) Qty:
1 Spool SoftFlex Beading Wire, fine (#49110) Qty:
Tools you will need (change quantity to 1 if you need them):
Flat Chain Nose Pliers (#51016) Qty:
Crimping Pliers (#51004) Qty:

Directions:
Step 1. Cut 3 strands of SoftFlex, about 9 inches each for our finished length. If you would like this bracelet to be a bit longer, cut more.
Step 2. On each of two strands of SoftFlex string, one 4mm Fuchsia Crystal and 10 Seed Beads. Repeat this pattern for each of the two strands 7 more times, ending with a 4mm Fuchsia Crystal. Set aside. These are strands A & C.

Step 3. On the remaining strand, string, 2 Seed Beads.
Step 4. Now string, one 3mm Fuchsia Crystal, 1 Heishi, one 6mm Rose Crystal, 1 Heishi, one 3mm Fuchsia Crystal and 3 Seed Beads. Repeat this pattern (Step 4) 7 more times.
Step 5. String one 3mm Fuchsia Crystal, 1 Heishi, one 6mm Rose Crystal, 1 Heishi, one 3mm Fuchsia Crystal, and 2 Seed Beads. This is strand B and will be somewhat longer than the strands A & C.
Step 6. On the end of strand A, string SoftFlex through 1 Crimp Bead, then through the end loop of one side of the Clasp and then back through the Crimp Bead. Snug up Crimp Bead to the Clasp and crush the Crimp Bead. Cut off excess or thread through beads. Repeat for the other side of Clasp. It may be easier to keep the Clasp Closed to do this.
Step 7. Repeat Step 6 for strand B, using the center loop of the Clasp.
Step 8. Repeat Step 6 for strand C, using the last end loop of the Clasp.
Step 9. Place the Crimp Covers over the Crimps and close gently with your Flat Nose Pliers. Enjoy!

Eclectic Etc., Inc. P.O. Box 10 Willow Grove, PA 19090-0010

Phone: 215-658-1711 Toll Free: 1-888-SHOP-ETC
Fax: 215-658-1191
Email: TheHeadBead@eebeads.com

Privacy Policy © Copyright 1996-2008 Eclectic Etc., Inc. All Rights Reserved No part of this page may be reproduced in any manner for commercial or non-commerical purposes without written permission from Eclectic Etc., Inc.